IDEA StatiCa Concrete v6.2.1.37451 x86 + x64 [Size: 476 MB ] ... IDEA StatiCa Concrete is used by engineers dealing with members/details of concrete structures. Designing is based on internal forces model created either in IDEA StatiCa or imported from FEA programs like Midas, Axis VM, SCIA Engineer and others.

Complete design of structural members and details + Beams, columns, frames, slabs + General/ predefined cross-sectional shapes + Straight/ curved, prismatic/ tapered + Reinforcement layout in zones along member, predefined templates, DXF export + EN 1992-1-1, EN 1992-2 plus National Annexes, SIA 262 + Comprehensive ULS/ SLS code checks + Non-linear deflections with long-term effects, 2nd order effects + Cross-section capacity – plain/ reinforced concrete + Flexure, shear, torsion, interaction of N, Vy, Vz, Mx, My, Mz, fatigue + Serviceability – stress limitations, crack width + Detailing + Response N-M-M, M-N kappa, short/ long-term stiffness + Corbel/ Bracket design using Strut&Tie method.

RCS – Reinforce Cross-Section:
BIM compliant – interface to various 3D FEA software + Complete design of plain/ reinforced/ prestressed concrete cross-sections + General/ predefined cross-sectional shapes of beams, columns, one-way and two-way slabs, walls, deep beams + Predefined reinforcement templates/ general reinforcement layout, DXF export + Pre/ post tensioned/ composite concrete-concrete cross-sections + Prestressing loss due to elastic strain, long-term loses + EN 1992-1-1, EN 1992-2 plus National Annexes, SIA 262 + Comprehensive ULS/ SLS code checks + Cross-section capacity in flexure, shear, torsion, interaction of N, Vy, Vz, Mx, My, Mz, fatigueServiceability – stress limitations, crack width/ decompression condition, brittle failure + Detailing + Stress-strain response N-M-M, M-N kappa, short/ long-term stiffness + Quick sectional check and/or detailed analysis where necessary
Eurocode supportive – references to EN provisions, tooltips, explanations, warnings, error messages.

Concrete Beam: 
Single span or continuous beam, cantilevers + Straight or curved in plane + Elevation in vertical plane + Standard or general cross-sections + Tapered beams in any span + Point, moment and line loads + Complete ULS and SLS combinations according to EN 1990 + Design according to EN 1992-1-1, EN 1992-2, SIA 262 + Reinforcement layout in zones along member, predefined templates
Complete ULS and SLS checks for zones and specific sections + Exact non-linear calculation of deflections with long term effects and cracks + Bill of material + 1xA4 or more detailed output report +Brief output overview or detailed protocol.

Concrete Column:
Column with one or two corbels + Free, fixed or flexible supports + Standard or general cross-sections of any shape + Forces and moments at the end or on corbels + Complete ULS a SLS combinations according to EN 1990 + Design according to EN 1992-1-1, EN 1992-2, SIA 262 + Reinforcement layout in zones along member, predefined templates + Complete ULS and SLS checks for zones and specific sections + Proper analysis of 2nd order effects + Overall interaction diagram + Bill of material + 1xA4 or more detailed output report.

Concrete Frame:
Plane frame or truss of arbitrary shape + Import of the shape from DXF + Standard or general cross-sections + Tapered beams and haunches + Point, moment, and line loads + Complete ULS a SLS combinations according to EN 1990 + Design according to EN 1992-1-1, EN 1992-2, SIA 262 + Reinforcement layout in zones along member, predefined templates + Complete ULS and SLS checks for zones and specific sections + Exact non-linear calculation of deflections  with long term effects and cracks + Proper analysis of 2nd order effects + Overall interaction diagram + Bill of material.

Concrete Slab:
Slab of arbitrary shape + Openings, internal lines and points + Import of the shape from DXF + Point or line, fixed or flexible supports + Point, moment, and line loads + General plane loads + Complete ULS a SLS combinations according to EN 1990 + Mesh generator, proper FE analysis + Design according to EN 1992-1-1, EN 1992-2, SIA 262 + Predefined reinforcement templates + Complete ULS and SLS checks in points + Longitudinal and shear reinforcement, proper shear check + Calculation of cracks + Bill of material.

Post a Comment

 
Top